大学城附近适合做什么生意:《转载》在NBMA网络点到多点模式下配置OSPF实际案例（配图）＋详细验证过程

《转载》在NBMA网络点到多点模式下配置OSPF实际案例（配图）＋详细验证过程2010年05月18日 星期二 17:02
一个点到多点网络被看作若干具有一个或多个邻居的点到点接口。当一个接口被配置给点到多点网络，就不需要DR/BDR，不需要定义邻居，这大大简化了给NBMA网络配置OSPF。使用端口命令 ip ospa network point-to-multioint可以给所有路由器设置网络类型。既不需要定义邻居，也不需要设置优先级，因为网络中没有DR/BDR。// 帧交换机frame-relay switchingint s2/0encapsulation frame-relayclock rate 64000frame-relay intf-type dceframe-relay route 200 int s3/0 300int s3/0encapsulation frame-relayclock rate 64000frame-relay intf-type dceframe-relay route 300 int s2/0 200frame-relay route 399 int s4/0 400int s4/0encapsulation frame-relayclock rate 64000frame-relay intf-type dceframe-relay route 400 int s2/0 399// R2 //int lo0ip ad 2.2.2.2 255.255.255.0int s2/0encapsulation frame-relayip ad 192.1.1.2 255.255.255.0ip ospf network point-to-multipoint //改变接口模式为点到多点frame-relay map ip 192.1.1.3 200 broadcastframe-relay map ip 192.1.1.4 200 broadcastrouter os 1network 2.2.2.2 0.0.0.0 area 0network 192.1.1.2 0.0.0.0 area 0// R3 //int lo0ip ad 3.3.3.3 255.255.255.0int s3/0encapsulation frame-relayip address 192.1.1.3 255.255.255.0ip ospf network point-to-multipoint //改变接口模式为点到多点frame-relay map ip 192.1.1.2 300 broadcastframe-relay map ip 192.1.1.4 399 broadcastrouter os 1network 3.3.3.3 0.0.0.0 area 0network 192.1.1.3 0.0.0.0 area 0// R4 //int lo0ip ad 4.4.4.4 255.255.255.0int s4/0encapsulation frame-relayip ad 192.1.1.4 255.255.255.0ip ospf network point-to-multipoint //改变接口模式为点到多点frame-relay map ip 192.1.1.2 400 broadcastframe-relay map ip 192.1.1.3 400 broadcastrouter os 1network 4.4.4.4 0.0.0.0 area 0network 192.1.1.4 0.0.0.0 area 0注意上述配置中没有任何特别操作，比如使用neighbor命令指明邻居，设置OSPF优先级等等，这就是点到多点模式下的特点。验证过程：一、首先来检查DR选举是否按我们的设计，R3被选举为DR，R2、R4不参与选举，同时注意网络类型是否为NBMA，hello时间间隔是否为30秒。。。。。。r3#sh ip os int s3/0
Serial3/0 is up, line protocol is up
Internet Address 192.1.1.3/24, Area 0
Process ID 1, Router ID 3.3.3.3, Network Type POINT_TO_MULTIPOINT, Cost: 64
Transmit Delay is 1 sec, State POINT_TO_MULTIPOINT,
Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5
Hello due in 00:00:18
Index 2/2, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 1, maximum is 2
Last flood scan time is 0 msec, maximum is 0 msec
Neighbor Count is 2, Adjacent neighbor count is 2
Adjacent with neighbor 4.4.4.4
Adjacent with neighbor 2.2.2.2
Suppress hello for 0 neighbor(s)r2#sh ip os int s2/0
Serial2/0 is up, line protocol is up
Internet Address 192.1.1.2/24, Area 0
Process ID 1, Router ID 2.2.2.2, Network Type POINT_TO_MULTIPOINT, Cost: 64
Transmit Delay is 1 sec, State POINT_TO_MULTIPOINT,
Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5
Hello due in 00:00:01
Index 2/2, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 1, maximum is 2
Last flood scan time is 0 msec, maximum is 0 msec
Neighbor Count is 1, Adjacent neighbor count is 1
Adjacent with neighbor 3.3.3.3
Suppress hello for 0 neighbor(s)r4#sh ip ospf int s4/0
Serial4/0 is up, line protocol is up
Internet Address 192.1.1.4/24, Area 0
Process ID 1, Router ID 4.4.4.4, Network Type POINT_TO_MULTIPOINT, Cost: 64
Transmit Delay is 1 sec, State POINT_TO_MULTIPOINT,
Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5
Hello due in 00:00:02
Index 2/2, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 1, maximum is 1
Last flood scan time is 0 msec, maximum is 0 msec
Neighbor Count is 1, Adjacent neighbor count is 1
Adjacent with neighbor 3.3.3.3
Suppress hello for 0 neighbor(s)二、接下来观察各路由器邻居建立情况：r2#sh ip os neiNeighbor ID Pri State Dead Time Address Interface
3.3.3.3 1 FULL/ - 00:01:33 192.1.1.3 Serial2/0r3#sh ip os neiNeighbor ID Pri State Dead Time Address Interface
4.4.4.4 1 FULL/ - 00:01:56 192.1.1.4 Serial3/0
2.2.2.2 1 FULL/ - 00:01:36 192.1.1.2 Serial3/0r4#sh ip os neiNeighbor ID Pri State Dead Time Address Interface
3.3.3.3 1 FULL/ - 00:01:37 192.1.1.3 Serial4/0三、最后验证路由：r2#sh ip ro 2.0.0.0/24 is subnetted, 1 subnets
C 2.2.2.0 is directly connected, Loopback0
3.0.0.0/32 is subnetted, 1 subnets
O 3.3.3.3 [110/65] via 192.1.1.3, 00:08:30, Serial2/0
4.0.0.0/32 is subnetted, 1 subnets
O 4.4.4.4 [110/129] via 192.1.1.3, 00:08:30, Serial2/0
192.1.1.0/24 is variably subnetted, 3 subnets, 2 masks
C 192.1.1.0/24 is directly connected, Serial2/0
O 192.1.1.3/32 [110/64] via 192.1.1.3, 00:08:30, Serial2/0
O 192.1.1.4/32 [110/128] via 192.1.1.3, 00:08:30, Serial2/0r3#sh ip ro
2.0.0.0/32 is subnetted, 1 subnets
O 2.2.2.2 [110/65] via 192.1.1.2, 00:08:54, Serial3/0
3.0.0.0/24 is subnetted, 1 subnets
C 3.3.3.0 is directly connected, Loopback0
4.0.0.0/32 is subnetted, 1 subnets
O 4.4.4.4 [110/65] via 192.1.1.4, 00:08:54, Serial3/0
192.1.1.0/24 is variably subnetted, 3 subnets, 2 masks
C 192.1.1.0/24 is directly connected, Serial3/0
O 192.1.1.2/32 [110/64] via 192.1.1.2, 00:08:54, Serial3/0
O 192.1.1.4/32 [110/64] via 192.1.1.4, 00:08:54, Serial3/0r4#sh ip ro2.0.0.0/32 is subnetted, 1 subnets
O 2.2.2.2 [110/129] via 192.1.1.3, 00:09:20, Serial4/0
3.0.0.0/32 is subnetted, 1 subnets
O 3.3.3.3 [110/65] via 192.1.1.3, 00:09:20, Serial4/0
4.0.0.0/24 is subnetted, 1 subnets
C 4.4.4.0 is directly connected, Loopback0
192.1.1.0/24 is variably subnetted, 3 subnets, 2 masks
C 192.1.1.0/24 is directly connected, Serial4/0
O 192.1.1.2/32 [110/128] via 192.1.1.3, 00:09:20, Serial4/0
O 192.1.1.3/32 [110/64] via 192.1.1.3, 00:09:20, Serial4/0

注意，在点到多点或点到点模式下，路由表中会自动生成32位主机路由。

转载自：http://blog.sina.com.cn/s/blog_56fdccdb010007jo.html