肿瘤康复的目的不包括:从无到有 建立水火箭
来源:百度文库 编辑:偶看新闻 时间:2024/04/29 13:59:43
从无到有 建立水火箭
火箭首先我购买了一个轮胎,用轮胎的嘴子做水火箭的喷嘴如下图:+=
论坛
- 喜欢液体火箭的朋友进来看看
回复引用
订阅TOP
rocketry
金牌会员
2#发表于 2010-11-24 05:23 | 只看该作者Making the hole, method 1:
I find it easier to get a hole centered by starting with a small bit to make a pilot hole, then enlarging it with larger bit. Here the pilot bit is 1/8 inch, the final bit 3/8 inch. The bottle gives me something to hold onto while the drilling is done. Yes, this is a crude method. Stay tuned for a better one.
回复引用
TOP
rocketry
金牌会员
3#发表于 2010-11-24 05:23 | 只看该作者回复引用
TOP
rocketry
金牌会员
4#发表于 2010-11-24 05:23 | 只看该作者A sharp knife is used for gross enlargement of the hole. It is then smoothed-up with a piece of 320 grit wet-or-dry paper rolled around a pencil. High tech.
回复引用
TOP
rocketry
金牌会员
5#发表于 2010-11-24 05:23 | 只看该作者The valve stem should be a tight fit. Fortunately, the neoprene covering tapers a bit from the threaded tip up to where the bulb used to be, so we make the cap-hole just big enough for the skinny end to fit into, and the fatter end will almost not pull out of.
回复引用
TOP
rocketry
金牌会员
6#发表于 2010-11-24 05:32 | 只看该作者Cutting the valve stemI start by cutting the neoprene around the brass core with a sharp knife, then hacksaw through the core. Yes, you can just hack through the rubber too, but the knife cuts it more cleanly. The sawed end is rough, but it is soft brass and surrounded by firm rubber. It is reasonably finger-friendly, so I resist the urge to true it up.
回复引用
TOP
rocketry
金牌会员
7#发表于 2010-11-24 05:32 | 只看该作者Note that there are two sizes of valve stems. Either will work, but the longer size ("2 inch") is much better. It gives me something to grab when attaching the valve to the air pump.
回复引用
TOP
rocketry
金牌会员
8#发表于 2010-11-24 05:32 | 只看该作者Test-fitting the valve stem.I smear a little grease on the valve-stem every time it is inserted. This makes the release much more consistent, I think. Palmer's Coco Butter skin cream is my favorite. Slick, non-toxic, and smells good. Vaseline works fine too.
回复引用
TOP
rocketry
金牌会员
9#发表于 2010-11-24 05:32 | 只看该作者So now we have a pressure-valve. Time to test it.
回复引用
TOP
rocketry
金牌会员
10#发表于 2010-11-24 05:33 | 只看该作者I fill the bottle about 1/2 full of water, screw on the plugged cap and attach the valve-stem to an air pump. The bottle is pointed bottom to the sky, the pump is started and the operator moved to a safe spot.Well, the first of these was launched without any stabilizer. It went flooey and flew all over. Good thrust, no stability, so the next one got a stick. It went fairly straight, but not very far. Got caught in a rocket-eating tree and is still there after two months. Stick heavy. Bad aerodynamics. Need a better stabilizer.
回复引用
TOP
rocketry
金牌会员
12#发表于 2010-11-24 05:33 | 只看该作者回复引用
TOP
rocketry
金牌会员
13#发表于 2010-11-24 05:33 | 只看该作者Also notice how nicely the trailing end of the stick is streamlined. Wish I had a wind tunnel! Here is Bottle 1 going together:回复引用
TOP
rocketry
金牌会员
14#发表于 2010-11-24 05:34 | 只看该作者回复引用
TOP
rocketry
金牌会员
15#发表于 2010-11-24 05:34 | 只看该作者Bottle 1 worked OK (as we shall see in the videos) but the weight of the fins suggested a larger motor would be of benefit. So I broke down and bought a 2-liter bottle of caffeinated sugar water, and drained it. Oh, the trials of rocketry.
回复引用
TOP
rocketry
金牌会员
16#发表于 2010-11-24 05:34 | 只看该作者Bottle 1 had complained a lot while I was assembling it, flexing, creaking, groaning and whining while I squeezed and twisted it to get the fins on. So Bottle 2 was bloated with water making it much stiffer while the fins were attached. That helped. More recently, I have been using the valve/nozzle and inflating the bottle with a few psi of air to make it stiff - this works even better.
回复引用
TOP
rocketry
金牌会员
17#发表于 2010-11-24 05:35 | 只看该作者The finsticks are taped on with a single strip of ... Duct Tape! My deepest apologies to all the Red Green fans out there, but this one is mine!
回复引用
TOP
rocketry
金牌会员
18#发表于 2010-11-24 05:35 | 只看该作者One little strip gets them all in place, then two long ones cinch them down, but not before:
The launch lug.
回复引用
TOP
rocketry
金牌会员
19#发表于 2010-11-24 05:35 | 只看该作者 I looked all over for a sturdy straw but had suffered a cleaning frenzy over Christmas break and thrown everything useful out. But there was still a broken arrow in my quiver. It had been lost in the field for a couple of years, no doubt stepped on by the Belgian mare a few times before the tractor found it. But a little manual straightening, trimming and sanding improved it a lot, and it is going to get covered with duct tape anyway. It's still kind of ugly. Sorry I showed it to you.回复引用
TOP
rocketry
金牌会员
20#发表于 2010-11-24 05:35 | 只看该作者The Pump
回复引用
TOP
rocketry
金牌会员
22#发表于 2010-11-24 05:36 | 只看该作者回复引用
TOP
rocketry
金牌会员
23#发表于 2010-11-24 05:36 | 只看该作者回复引用
TOP
rocketry
金牌会员
24#发表于 2010-11-24 05:36 | 只看该作者回复引用
TOP
rocketry
金牌会员
25#发表于 2010-11-24 05:37 | 只看该作者This funnel fits between the fins so nicely I should patent it. The bottle is filled about 1/3 full of water and the cap with blowout valve screwed on tight. Notice the mismatched cap color. There is a reason for that (see below.) The rocket is set upright on a model-rocket launch rod stuck into the ground and the pump connector attached. Here I am using the short valve stem because that's what I had. The long ones are much better - they give me something to hold onto while attaching the pump
回复引用
TOP
rocketry
金牌会员
26#发表于 2010-11-24 05:37 | 只看该作者 本帖最后由 rocketry 于 2010-11-24 05:38 编辑The aluminum pan is the "blast deflector" and serves the purpose of keeping the pump dry. It sort of works, but after awhile the pump stopped working. I had to disassemble it and clean the mud out of it. Ever since I have been throwing a cover over it.
So here, finally, are some launches. Not all are good ones. Each video is 1.4 megs for 15 seconds of video, much of which is the sound of the pump running.
回复引用
TOP
rocketry
金牌会员
27#发表于 2010-11-24 05:38 | 只看该作者 本帖最后由 rocketry 于 2010-11-24 05:39 编辑I heard large vehicles driving up to my house, then a horn. Out of water anyway, I picked up the pieces and headed back. It was the tree-trimmers hired by our local power company. They were scouting the easements getting ready to thrash the brush back from the power lines. I showed them the water rocket. They were intrigued. I fired it a few times. One guy was particularly interested, and suggested using PVC pipe. I thought to myself: No, that's too heavy. Even for thinwall, if you could find thinwall big enough for a drink bottle to fit into... Bing! The light comes on. I am thinking airframe, he means pressure vessel. Just add fins and the vessel becomes the airframe. I just might have to experiment with that option soon
回复引用
TOP
rocketry
金牌会员
28#发表于 2010-11-24 05:39 | 只看该作者In the meantime, here are a few gratuitous shots from the field:回复引用
TOP
rocketry
金牌会员
29#发表于 2010-11-24 05:40 | 只看该作者Another little revelation: I have been assuming that my off-vertical launches were the result of a poorly-centered nozzle hole in the cap. But during testing, I noticed that some rockets flew funny every time, always arced in the same direction, and using a different nozzle-cap made little difference. Now I believe that some PET bottles have off-center necks, or perhaps are not straight. These defects aren't obvious from a casual visual inspection, so I choose my bottles more carefully now.
回复引用
TOP
rocketry
金牌会员
30#发表于 2010-11-24 05:40 | 只看该作者Caps RevisitedThe Dasani problem: An alternative to drilling
Notice that the bottle caps used in Bottle Rockets 1 and 2 are all blue. That is because the nozzle holes are drilled, and I have found only one brand that has caps suitable for drilling: Dasani bottled water. Dasani caps do not have a gasket. Coke, Pepsi, and all their siblings have a thin, soft plastic gasket inside the cap which provides the seal. Remove the gasket and they leak. Drilling destroys the gasket. So if you are going to drill, get caps from Dasani bottles even if your tap water is good.
回复引用
TOP
rocketry
金牌会员
32#发表于 2010-11-24 05:41 | 只看该作者回复引用
TOP
rocketry
金牌会员
33#发表于 2010-11-24 05:41 | 只看该作者回复引用
TOP
rocketry
金牌会员
34#发表于 2010-11-24 05:41 | 只看该作者回复引用
TOP
rocketry
金牌会员
35#发表于 2010-11-24 05:41 | 只看该作者回复引用
TOP
rocketry
金牌会员
36#发表于 2010-11-24 05:42 | 只看该作者Water-Rocket Cap Holing JigAllows much better-centered nozzle holes.Plus it is much quicker - I can crank out 2 or 3 nozzle-caps per minute.
To make the jig, a PET bottle neck is cut off just below the flange.
Since the hacksaw invariably angles, the base is sanded flush to the flange.
Using a better saw might eliminate the need for sanding.
回复引用
TOP
rocketry
金牌会员
37#发表于 2010-11-24 05:42 | 只看该作者A PVC pipe fitting is used to complete the jig. It is a 1/2 male threaded adapter. The other end is 1/2 inch female slip, but that doesn't matter. The male threaded portion happens to be a snug fit into the bottle neck, providing good centering. Notice that there are two PVC adapters. One has hexagonal flanges, the other a knurled exterior. For my purposes, the flat hex flanges are better by far, fitting the flat jaws of my drill-press vise well, so that is the one I will use
回复引用
TOP
rocketry
金牌会员
38#发表于 2010-11-24 05:42 | 只看该作者The bottle-neck is fastened to the PVC fitting with 5-minute epoxy. Yes, I know. Epoxy is not the best glue for either of these plastics. But this is a low-stress application. Epoxy is quick, easy, and more than adequate.
回复引用
TOP
rocketry
金牌会员
39#发表于 2010-11-24 05:43 | 只看该作者 Here is the first of these (left) and today's project (right.) Notice the sloppy glue-job on the first one. I got in a hurry. Serves me right. Works OK anyway.Mounting the jig. Here I have cut the head off a 3/8 inch steel bolt and mounted it in the drill-press chuck. The plastic jig is clamped in the vise, centered under the bolt, and tightened down. Precise centering is difficult. This is where a good indexing vise would be helpful. Guess I ought to buy one.
回复引用
TOP
rocketry
金牌会员
回复引用
TOP
rocketry
金牌会员
42#发表于 2010-11-24 05:44 | 只看该作者回复引用
TOP
rocketry
金牌会员
43#发表于 2010-11-24 05:44 | 只看该作者回复引用
TOP
rocketry
金牌会员
44#发表于 2010-11-24 05:44 | 只看该作者回复引用
TOP
40#发表于 2010-11-24 05:43 | 只看该作者Since semi-retiring my 4x4 airframes, they have found many uses. This one the torch bearer. It serves most proudly.回复引用
TOP
关于水火箭的~
水火箭制作方法
怎么制作水火箭
怎么制作水火箭?
水火箭的做法
水火箭 降落伞设计
如何制作二级水火箭?
如何提高水火箭射程
怎样制作二级水火箭?
请简述水火箭的制作原理
谁知道MP3从无到有的过程?
精子是怎么从无到有的?
如何才能从无到有成为一个会计师
谁会制造二级水火箭,特别是接口处!
请问谁有水火箭的制作结构诗意图
真实火箭的发射原理,不是水火箭
如何制作一个多级发射的水火箭?
请问水火箭的尾翼几片合适?简要说明
水火进行曲
学生怎样才能从无到有的经营经商?
制作水火箭整流罩用的材料哪些地方能找到??
古代火箭,现代火箭,水火箭分别利用的是哪两个力的相互作用?
什么是水火难容?
水火相溶打一字